Optical Ring V2

dminner · Post by **dminner** » Sat Sep 22, 2018 3:02 pm

Here are some quick and dirty guitar sounds:

https://m.youtube.com/watch?v=esl7dt45wKk

Chankgeez · Post by **Chankgeez** » Sat Sep 22, 2018 3:09 pm

fuzzisokiguess · Post by **fuzzisokiguess** » Sat Sep 22, 2018 4:26 pm

Quick? Check.

Dirty? Check.

Crushed this one. UC is right (ya know), the photo of the guts looks suitable for framing- the lines and curves!

And promise to stop at V2 and not make an even more awesome v3, k? Thx.

dminner · Post by **dminner** » Mon Sep 24, 2018 12:26 pm

fuzzisokiguess wrote:Quick? Check.

Dirty? Check.

Crushed this one. UC is right (ya know), the photo of the guts looks suitable for framing- the lines and curves!

And promise to stop at V2 and not make an even more awesome v3, k? Thx.

No plans for a V3. I don't know what else I could add at this point

jrfox92 · Post by **jrfox92** » Tue Sep 25, 2018 7:05 pm

CV control over every knob.

dminner · Post by **dminner** » Sat Sep 29, 2018 6:01 pm

New boards are nearly populated

dminner · Post by **dminner** » Sun Sep 30, 2018 3:06 pm

Loading

dminner · Post by **dminner** » Mon Oct 01, 2018 11:17 pm

1-4 of the 8 are finished

dminner · Post by **dminner** » Tue Oct 02, 2018 9:37 am

Make that 5. Three have already been claimed but the other two are available and the last three will be done later in the week

https://www.instagram.com/p/Bobk6hYnAgV ... =addpedals

dminner · Post by **dminner** » Wed Oct 03, 2018 7:17 am

Expression control:

https://instagram.com/p/Boc43BSHTna/

crochambeau · Post by **crochambeau** » Wed Oct 03, 2018 9:55 am

These are sharp as hell, nice work!

One of these years I'll be in position to grab one.

dminner · Post by **dminner** » Sun Oct 07, 2018 10:08 pm

Well, the 8 in this limited run just got more limited...final wiring on the last two tonight...and there ended up only being 7. Working with the vintage enclosures had several challenges...the stupidest presented itself tonight. One lid was nearly 1/4” shorter than all the others...so bottom does fit. So yeah. Run of 7

2 remaining if anyone wants one.

crochambeau · Post by **crochambeau** » Mon Oct 08, 2018 5:19 pm

Would trimming the wall on the bottom plate put that one back on the road, or would you have completely run out of transformer room with the chopped look?

dminner · Post by **dminner** » Tue Oct 09, 2018 9:52 am

crochambeau wrote:Would trimming the wall on the bottom plate put that one back on the road, or would you have completely run out of transformer room with the chopped look?

No, it is short in the worst way. Not the z, but rather the y on the face. So essentially the folded bottom plate will no longer hold it up. If that makes since.

dminner · Post by **dminner** » Tue Oct 16, 2018 12:00 pm

[youtube]http://m.youtube.com/watch?v=yQH4BYyyLpo[/youtube]

ilovefuzz.com

Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2

Re: Optical Ring V2